Coats CDH-9551 Electric-Hydraulic Tire Changer Manual de usuario

OPERATING AND MAINTENANCE INSTRUCTIONSElectro-Hydraulic Tire ChangerFor Medium and Large Size TiresCHD-9551READ these instructions before placing unit

10DANGER! When the spindle carrier arm is lowered, there is always a potential for crushing anything in its movement range. Always work from the posit

1113.1RIM CLAMPING13OPERATION WARNING!In rim clamping, make sure that jaws are properly positioned on the rim, so as to prevent the tire from falling

1213.2DANGER!Do not very the work area with a wheel clamped on the tire changer and lifted up from the oor. TUBELESS AND SUPERSINGLE TIRES BEAD LOOSE

13Remember that the stronger the tire’s adherence to the rim, the slower must be the disk’s penetration.7) Move the tool carrier arm (14, Fig. F) back

14-Place the tool carrier arm in the working position, then the bead disk to push against the inside face of the tire (see g. H). It’s is best to do

15 L M6) Position the bead loosener disk against the second bead of the tire and turn the spindle until the g-clamp is at the low point (at 6 o’clock

16MOUNTING WITH THE HOOKED TOOL1) Follow the steps described in points 1,2,3,4,5 for mounting with the disk.2) Move the tool carrier arm to its non-wo

171) Tip the tool carrier arm (14, Fig. D) to its non-working position. Move it to the outside face of the tire and rehook it in this position.2) Rota

184) Put the tire on the ramp and lower the spindle (make sure the g-clamp is at the high point) to hook the rst bead on the g-clamp.Take the mobile

19 S T16) Turn the spindle until the valve is at the bottom (6 o’clock).17) Inate the inner tube a little (until it has no folds) so as not to pinch

2INDEX1 - GENERAL INFORMATION...

2030) Move the ramp to release the tire from the spindle.31) Remove the tire.13.4TIRES WITH SPLIT RING BEAD LOOSENING AND DEMOUNTINGTIRE ASSEMBLIES WI

212) Lower the tool carrier arm (14, Fig. D) to its work position until its hook has engaged into position on the carriage.3) Use the joystick to pos

22MOUNTING TIRE ASSEMBLY WITH 3-PIECE SPLIT-RINGS1) Move the tool carrier arm to its non-working position. If the rim has been removed from the spindl

237) Move the tool carrier arm to the outside in its work position with the bead loosener disk facing the tire.If the split-ring is not inserted sufc

2415TROUBLE SHOOTINGPROBLEMTROUBLE SHOOTINGAfter having switched on the main power switch on the electric pack, the general warning light does not lig

25The manufacturer’s Serial plate is xed on the back of the machine. If gives the following information:1- Manufacturer information2- Model3- Serial

HENNESSY Industries, INC1601 J.P. Hennessy Drive, LaVergne, TN 37086-3565 USA Toll Free 800-688-6496www.ammcoats.com

3Pump motorGear-box motorHandles rim fromMax. wheel diameterMax. wheel widthMax. wheel weight Weight (with standard accessories)Acoustic pressure leve

4lbs 2745(KG. 1245)B/2B/1A/26Once the packing material has been removed, check the machine visually for any signs of damage.Keep the packing materials

5A21431The universal tire-changer must be installed on a levelled concrete oor at least 8” (20 cm.) thick, with a minimum concrete quality of B25 in

67.3ELECTRIC HOOK UPBefore making any electric hook up, check to be certain that the mains voltage corresponds to that stamped on the voltage tag (at-

78DACabcdefgh1095811132422181413191715LAYOUT OF FUNCTIONAL PARTS1 - Lifting bracket2 - Self-centering chuck holding arm3 - Self-centering chuck4 - Sli

89IDENTIFYING WARNING SIGNALSWARNING:Unreadable and missing warning labels must be replaced immediately. Do not use the tyre changer if one or more la

910CONTROLS DESCRIPTIONThe diagram B/8 illustrates the various working positions (A,B,C,D) referred to in the following pages describing how to use th