Coats CDH-9043 Electric-Hydraulic Tire Changer Manual de usuario

OPERATING AND MAINTENANCE INSTRUCTIONSElectro-Hydraulic Tire ChangerFor Medium and Large Size TiresCHD-9043READ these instructions before placing unit

10First use handle (15, Fig. D) to tip the arm to this position. 1) Move the joystick (8, Fig. C) up (a): the spindle carrier arm (2, Fig. A) should l

1113.1RIM CLAMPING13OPERATION WARNING!In rim clamping, make sure that jaws are properly positioned on the rim, so as to prevent the tire from falling

1213.2The most convenient locking position on the rim may be selected according to gs E/1 - E/2 - E/3 - E/4 - E/5 and E/6. Always remember that the s

135) Rotate the wheel and at the same time, advance the bead-breaker plate with small forward movements following the prole of the rim, with the plat

14- Insert lever (17, Fig. I) between rim and bead at the right of the tool.-Press down on the lever and lower the wheel to bring the edge of the ri

15TYRE MOUNTING WITH THE DISKFollow these steps:1) If the rim has been removed from the spindle, put it back on the spindle as described in the sectio

16 NMOUNTING WITH THE HOOKED TOOL1) Follow the steps described in points 1,2,3,4,5 for mounting with the disk.2) Move the tool carrier arm to its non

17 O N13.3TUBE TIRESBEAD LOOSENINGWARNING: release ination tire so that the valve, coming inside the rim, is not an obstacle during bead loosening.

18Take the mobile control unit to work position D.10) Move the tool carrier arm to the inside face of the tire, turn the hook tool 180° and lower the

199) Move to the outside of the tire and check the exact position of the hook visually and adjust it as needed. Then turn the spindle clock-wise until

2INDEX1 - GENERAL INFORMATION...

20DANGER! POTENTIALLY HAZARDOUS OPERATION!Do it manually only if you are certain you can keep the tire assembly balanced. For large and heavy tires an

21 Z WTake the mobile control unit to work position B.14) Move the ramp towards the outside until the tire is completely off the rim. Watch out for t

2212) Lower the spindle until the tire is resting on the ramp.13) Move the ramp towards the outside until the tire together with the split ring comes

23YTake the mobile control unit to work position B.3) Move the platform to be able to place the tire on it.4) Lower or raise the spindle to centre th

2414ORDINARY MAINTENANCEWARNING!Each maintenance operation must be performed only after the disconnetion of the plug from electric netw

25PROBLEMAfter having switched the general button on the general warning light also switches on but the motor on the hydraulic power pack doe

2620 ACCESSORIESThe manufacturer’s Serial plate is xed on the back of the machine. If gives the following information:1- M anu f act u r er i n fo

27

HENNESSY Industries, INC1601 J.P. Hennessy Drive, LaVergne, TN 37086-3565 USA Toll Free 800-688-6496www.ammcoats.com

3Pump motorGear-box motorHandles rim fromMax. wheel diameterMax. wheel widthMax. wheel weight Weight (with standard accessories)Acoustic pressure leve

4TRANSPORT5The machine is delivered in:1- in a wooden crate with palletThe machine must be handled with a fork-lift truck with the forks positioned as

5B/598.4 inches(2,500 mm)7.2Maximum machine space requirements are 88.2X6.3 inches (2,240x 1,640 mm) with a minimum distance from walls as shown in th

63,931,965,903,933,93 inches7.3ELECTRIC HOOK UPBefore making any electric hook up, check to be certain that the main voltage corresponds to that stam

78LAYOUT OF FUNCTIONAL PARTSWARNING! During all operations, keep hands and other parts of the body as far as possible from moving parts of the mach

8D14151817139IDENTIFYING WARNING SIGNALSWARNING:Unreadable and missing warning labels must be replaced immediately.Do not use the tire changer if one

910IDENTIFYING CONTROLSThe diagram B/8 illustrates the various working positions (A,B,C,D) referred to in the following pages describing how to use t