Coats 9500R Electro-Hydraulic Tire Changer Manual de usuario

1601 J. P. Hennessy Drive, LaVergne, TN USA 37086-3565 615/641-7533 800/688-6359 www.ammcoats.com Manual Part No.: 8184345 02HENNESSY INDUSTR

Operating Instructions4.0 ControlsBefore operating the machine ensure that you thor-oughly understood the operation and function of all thecontrols.1.

COATS 9500R Tire Changer • 75.0 Mounting and Demounting - GeneralPrecautionsBefore mounting a tire on a rim, pay atten-tion to the following:A.The r

5.2 Demounting Tubeless Truck Tires (Up to13”Wide)The tubeless truck tires are mounted on drop-centerrims with a conical base. It is possible to demo

COATS 9500R Tire Changer • 97. Continue rotating the chuck, moving tool holdercarriage towards the outside until the beads aredemounted from the rim

5.3 Mounting Tubeless Truck Tires (Up to13”Wide)1. Liberally lubricate the entire inner surface of therim and the tire beads. Attach the mounting clam

COATS 9500R Tire Changer • 11The mounting clamp is at approximately 11 o’clock.Fig.27Never use hand pressure to hold the tireonto the rim as persona

5.4 Demounting Duplex and SupersingleTubeless Truck Tires (Over 13” Wide)Note: For this operation the mount/demount tool isrequired.1. Loosen the bea

COATS 9500R Tire Changer • 133. Rotate the chuck clockwise. Normally less than1/4 of a revolution is sufficient to mount the first bead(fig.33).Fig.

5.6 Demounting Tires From Multi-PieceRim/Wheel Assemblies (Tube Type Tires)The multi-piece rim/wheel assembly can be in two ormore pieces (fig.36).Fig

COATS 9500R Tire Changer • 155.7 Mounting Tires Onto Multi-pieceRim/Wheel Assemblies1. Roll the tire on the foot board (the tube and flapmust be in

ii • COATS 9500R Tire ChangerTable of ContentsSafety Instructions . . . . . . . . . . . . . . . . . . . .ii-ivDefinitions of Hazard Levels . . . . .

5. Place the hook tool between bead and rim(fig.44).Fig.446. Lift the chuck arm to move the hook tool awayfrom the rim edge (1” or 2-3 cm).Move the to

COATS 9500R Tire Changer • 1710. Place the hook tool as in fig.48. The edge of thehook should be about 1” (2-3 cm) away radically fromthe rim edge a

6.0 MaintenanceBefore starting any maintenance operation ensurethat no wheel is mounted on the chuck and that themachine is disconnected from the elec

COATS 9500R Tire Changer • 19TroublePump motor turns but none of thehydraulic movement works.Pump motor does not turn but thechuck motor operates no

8184345 02 01/04 © Copyright 2003 Hennessy Industries and COATS®All Rights Reserved Printed in USATruck Tire Changer Warranty PolicyThe COATS®Company

COATS 9500R Tire Changer • iiiOperator Protective EquipmentPersonal protective equipment helps make tire servic-ing safer. However, equipment alone

iv • COATS 9500R Tire ChangerBead Loosening SafetyNEVERplace any part of your body between the beadloosener disc and the tire/wheel, severe bodily inj

COATS 9500R Tire Changer • 11.0 IntroductionCongratulations on purchasing the COATS®9500RElectro-Hydraulic Tire Changer.This tire changer is designe

1.5 SpecificationsElectro-hydraulic tire changer for tubeless truck tires.Weight with Standard Acc. 2270 lbs. (1032 kg)Electric Specifications 220VAC,

COATS 9500R Tire Changer • 31.8 Optional Accessories#874021852 Clamp for Light-Alloy Rims (fig.5).To hold the bead when mounting tires on light-allo

2.0 Carriage InstructionsThe machine is crated in a wooden box of appropriatestrength.The box is mounted on a pallet.Handling of the machine must be p

COATS 9500R Tire Changer • 53.0 InstallationInstructionsTo install the machine proceed as follows:A. Before raising the machine, ensure that the chu